





Shop / marey gas 6l 1.58 gpm lp tankless water heater
Portable Gas Tankless Water Heater for RVs and Outdoor Use
Add to wishlist
Category: marey gas 6l 1.58 gpm lp tankless water heater

About this item
- 𝗚𝗼𝗼𝗱 𝗳𝗼𝗿 𝗢𝗳𝗳-𝘁𝗵𝗲-𝗚𝗿𝗶𝗱 - Runs on a standard 20 lb. liquid propane tank and is equipped with an electronic ignition powered by two D-cell batteries. Can be used in a variety of scenarios: while you're camping RVing hunting hanging poolside washing your pets or horses cleaning your vehicle or even in your tiny home greenhouse or cabin house.
- 𝗦𝗮𝗳𝗲𝘁𝘆 𝗜𝗻𝘀𝘁𝗮𝗹𝗹𝗮𝘁𝗶𝗼𝗻 𝗧𝗶𝗽𝘀 - To avoid gas leakage caused by improper sealing of the water heater DO NOT TWINE TEFLON TAPE between the gas regulator and gas inlet pipe. Always check gas leakage before operation.
- 𝟭-𝗬𝗲𝗮𝗿 𝗖𝘂𝘀𝘁𝗼𝗺𝗲𝗿 𝗦𝘂𝗽𝗽𝗼𝗿𝘁 - We provide a 1-year Warranty against manufacture defects and lifetime customer support.
- Enhanced Safety Protection System - Compliant with CSA certification, meeting Canadian and US standards. It includes safeguards against overheating, low water flow, dry combustion, freezing conditions, high water pressure, and includes a flame failure device.
- 𝗪𝗵𝗮𝘁'𝘀 𝗜𝗻𝗰𝗹𝘂𝗱𝗲𝗱 - GASLAND BE158 Tankless Water Heater CSA certified gas regulator and hose 5 feet On/Off Switch Shower Head mounting hardware garden hose adapter Manual.
- 𝟭.𝟱𝟴𝗚𝗣𝗠/𝟲𝗟 𝗣𝗿𝗼𝗽𝗮𝗻𝗲 𝗪𝗮𝘁𝗲𝗿 𝗛𝗲𝗮𝘁𝗲𝗿 - Maximum power output 41 000BTU/Hr. The temperature rise is 109.4℉ (43℃) at its highest point and 55.4℉ (13℃) is at its lowest point of 1.58 GPM. Also 1.58 gallons of hot water can be produced per minute at a flow rate of 1.58 GPM. Low water pressure start-up just need 3.6 PSI of water pressure to start.
- 𝗠𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗧𝗶𝗽𝘀 - Designed for portable outdoor use. It is splash-proof and can manage a little drizzle however prolonged exposure to rain/water will damage the internal components. We recommend using and storing your water heater in a dry place. For the winter please drain out the water by disconnecting the drain plug and storing it in a warm and dry area.
- 𝗟𝗘𝗗 𝗗𝗶𝗴𝗶𝘁𝗮𝗹 𝗗𝗶𝘀𝗽𝗹𝗮𝘆 - Bright power the temperature readout so as to not get the water too hot or cold.




















